Martin Atomic LED

Martin Atomic LED


Martin Atomic LED Manual

All prices shown are list prices, for a 1 week hire period. All of our trade customers are eligible for discount. Get in touch with us to receive an individually tailored quote.

Add To Cart

Dynamic Effects
Strobe: 0.289 - 16.667 Hz, variable flash rate, intensity and durationSpecial effects: Blinder, ramp up/down, random flash, lightning. spikes, pre-programmed FXAura (secondary LED array illumination) color mixing: RGB

Length: 245 mm (9.7 in.)Width: 425 mm (16.8 in.)Height: 240 mm (9.5 in.)Weight: 7.8 kg (17.2 lbs.)All data including mounting bracket

Optics and Photometric Data
Max. total output: 180 000 lumens*Beam (strobe) arrayLight source: 228 x Cree XLamp XP-L, 10 W white LEDs (color temperature 5700 K)Resolution: 8-bitDimming, above 16.7% output intensity: Current-controlled, flicker-freeDimming, below 16.7% output intensity: PWM (refresh rate 6000 Hz)Minimum LED lifetime: 50 000 hours**Aura (backlight) arrayLight source: 64 x Osram RGB LEDsResolution: 8 bits per color plus 8-bit dimmingDimming: PWM (refresh rate 1001 Hz)Minimum LED lifetime: 50 000 hours***For full photometric data, click on Photometrics in menu bar**To >70% output, figure obtained under manufacturer’s test conditions

Control and Programming
Control systems: DMX, RDMDMX channels: 3/4/14Setting and addressing: Control panel with backlit monochrome graphic displayDMX compliance: USITT
DMX512-ARDM compliance: ANSI/ESTA E1.20 RDMTransceiver: 
RS-485Firmware update: USB memory key or
via DMX with Martin™ M-DMX interface

Mounting points: Two pairs of quarter-turn fastener points, M12 holes in adjustable bracketOrientation: AnyMinimum distance to combustible materials: 200 mm (8 in.) from fixtureMinimum distance to illuminated surfaces: 1 m (3 ft. 4 in.) from fixtureLocation: Indoor use only, must be fastened to structure or surface

Color: BlackHousing: Steel. high-impact thermoplastic, flame-retardant to UL 94 5VAProtection rating: IP 20

AC power: 100-240 V~ nominal, 50/60 HzPower supply unit: Auto-ranging electronic switch modeMaximum power consumption: 740 WRated current consumption: 3.5 - 8.4 APeak current consumption: 17.7 ATypical half-cycle RMS inrush current: 17.7 A

AC power: Neutrik PowerCON TRUE1 male socketDMX data in/out: 5-pin locking XLRAtomic Colors color gel scroller: 4-pin locking XLRSoftware upload: USB 2.0

Cooling: Forced air (temperature-regulated, low noise, user-definable fan settings)Maximum ambient temperature (Ta max.): 40° C (104° F)Typical heat dissipation (calculated, +/- 10%): 2270 BTU/hr.

Typical Power and Current
100 V, 60 Hz: 663 W, 6.8 A, PF 0.98120 V, 60 Hz: 655 W, 5.7 A, PF 0.96208 V, 60 Hz: 645 W, 3.5 A, PF 0.89230 V, 50 Hz: 642 W, 3.2 A, PF 0.88240 V, 50 Hz: 642 W, 3.1 A,
PF 0.87Measurements made at nominal voltage with all LEDs at full
strobe intensity.
Allow for a deviation of +/- 10%. Allow for peak currents that exceed
these figures when using the blinder effect. PF = power factor.